Skip to main content
Wikispaces Classroom is now free, social, and easier than ever.
Try it today.
Pages and Files
Help and tools
Some Editing Tools
About Our Members
Amine gas treating
Fluid catalytic cracking
Hydrocarbon dew point
Liquefied natural gas
Natural gas processing
Petroleum crude oil
Petroleum refining processes
Pressure relief valve
Process flow diagrams
Oil tanker propulsion engine
Transport phenomena terms
Vacuum distillation (refinery)
ADMS (Atm. Disp. Mod. Sys.)
Air dispersion modeling
Air dispersion terminology
Air pollutant concentrations
Air pollution dispers. models
Air pollution emissions
Air quality measurement
Air Quality Modeling Group
Air quality monitoring design
Air Resources Laboratory
Desert Research Institute
Dispersion Modeling Bibliog.
Dispersion Model Validation
Dutch Meteorological Institute
European Environment Agency
Met Office Dispersion Modeling
Stack Gas Dispersion (book)
Wind profile power law
is one of the gas laws and was formulated by the British chemist, William Henry, in 1803. It states that:
At a constant temperature, the amount of a given gas dissolved in a given type and volume of liquid is directly proportional to the partial pressure of that gas in equilibrium with that liquid.
Formula and Henry constant
Henry's law may be mathematically expressed as:
is the partial pressure of the solute above the solution
is the concentration of the solute in the solution (in one of its many units)
is the Henry's Law constant, which has units such as L
Some values for
): 769.2 L
carbon dioxide (CO
): 29.4 L
): 1282.1 L
when these gases are dissolved in water at a temperature of 298 K.
As shown in Table 1 below, there are other forms of Henry's law each of which defines the constant
differently and requires different dimensional units.
The form of the equation presented above is consistent with the example numerical values presented for oxygen, carbon dioxide and hydrogen and with their corresponding dimensional units.
Note that for the above values, the unit of concentration,
, was chosen to be molarity (i.e., mol/L). Hence the dimensional units:
is liters of solution,
is the partial pressure of the gaseous solute above the solution (in atmospheres of
refers to a mol of the gaseous solute in the solution. Also note that the Henry's law constant,
varies with the solvent and with the temperature.
Forms of Henry's Law
There are various forms Henry's law which are discussed in the technical literature.
= moles of gas per liter of solution
= liters of solution
= partial pressure above the solution, in atmospheres of absolute pressure
= mole fraction of gas in solution ≈ moles of gas per mole of water
= atmospheres of absolute pressure
As can be seen by comparing the equations in the above Table 1, the Henry's law constant
is simply the inverse of the constant
. Since all
values may be referred to as the Henry's law constants, readers of the technical literature must be quite careful to note which version of the Henry's law equation is being used.
It should also be noted the Henry's law is a limiting law that only applies for
solutions. The range of concentrations in which it applies becomes narrower the more the system diverges from ideal behavior. Roughly speaking, that is the more chemically
the solute is from the solvent.
It also only applies for solutions where the solvent does not react chemically with the gas being dissolved. A common example of a gas that does react with the solvent is carbon dioxide (CO
), which rapidly forms hydrated carbon dioxide and then carbonic acid (H
) with water.
Temperature dependence of Henry's law constant
When the temperature of a system changes, the Henry's law constant will also change.
This is why some people prefer to name it the
Henry's law coefficient
. There are multiple equations assessing the effect of temperature on the constant. These forms of the van't Hoff equation are examples:
= Henry's law constant as defined in the first section of this article.
= A constant, in kelvins. Note that the correct sign of
depends on whether
= Any given temperature, in kelvins
= the standard state temperature of 298 K
The above equation is an approximation only and should be used only when no better experimentally derived formula for a given gas exists.
The following Table 2 lists some values for the constant
in the equation above:
Because the solubility of gases usually decreases with increasing temperature, the partial pressure a given gas concentration has in a liquid must increase. While heating water (saturated with nitrogen) from 25 °C to 95 °C, the solubility will decrease to about 43% of its initial value. The partial pressure of CO
in seawater doubles with every 16 K increase in temperature.
may be regarded as:
= the enthalpy of solution
= the universal ideal gas constant
F.F. Lee (2007).
Comprehensive analysis, Henry's law constant determination, and photocatalytic degradation of polychlorinated biphenyls (PCBs) and/or other persistent organic pollutants (POPs)
, Ph.D. dissertation, State University of New York at Albany, pp. 199-201. Published by ProQuest.
Robert G. Mortimer (2000),
, Second Edition, Academic Press, ISBN 0-12-508345-9
Editors: D.W. Green and Robert H. Perry (1984),
Perry's Chemical Engineers' Handbook
, 6th Edition, McGraw-Hill, page=14-9, ISBN 0-07-049479-7
Online Introductory Chemistry: Solubility of gases in liquids
Francis L. Smith and Allan H. Harvey (Sept. 2007), "Avoid Common Pitfalls When Using Henry's Law",
Chemical Engineering Progress (CEP)
, pp. 33-39
Same as Reference 5
North Carolina State University CH 431/Lecture 14
An extensive list of Henry's law constants, and a conversion tool
Same as Reference 5
Same as Reference 5
Same as Reference 3. See pages 3-101 to 3-103 for tabulated Henry's law constant values versus temperature for various gases.
Same as Reference 8
T. Takahashi et al (2002),
"Global sea-air CO2 flux based on climatological surface ocean pCO2 and seasonal biological and temperature effect"
Deep Sea Res. II
, 49, (9-10), pp. 1601– 1622.
help on how to format text
Turn off "Getting Started"